Shoulder Multi Layer

C3D ShoulderMultiLayer — 9-layer shoulder, tapered Subbase3, layers end on the daylight face

At a glance


Kind	Subassembly (composed into an assembly)
Domain	Road
Civil 3D equivalent	`ShoulderMultiLayer`
Geometry	22 points, 32 links, 9 shapes

Parameters

Defaults are the metric values the palette inserts. Every parameter can be driven by an expression or a target.

Parameter	Type	Default	Meaning
`Side`	+1 right of the baseline, −1 left	Right (+1)	+1 Right / -1 Left
`ShoulderWidth`	number (metres unless the description says otherwise)	2.4	Attachment to hinge (m)
`ExtensionPave2`	number (metres unless the description says otherwise)	0.05	Pave2 stub length (m)
`ExtensionPave3`	number (metres unless the description says otherwise)	0.1	Pave3 stub length (m)
`DefaultShoulderSlope`	cross slope as a ratio (−0.02 = 2 % fall)	-0.06	Shoulder cross slope (SE fallback)
`SubbaseDaylightType`	number (metres unless the description says otherwise)	0	0 = hold slope, 1 = hold width (derive slope)
`DaylightSlope`	cross slope as a ratio (−0.02 = 2 % fall)	0.25	Daylight slope when held
`DaylightWidth`	number (metres unless the description says otherwise)	3	Daylight width when held (m)
`Pave1Depth`	number (metres unless the description says otherwise)	0.025	Pave1 depth (m)
`Pave2Depth`	number (metres unless the description says otherwise)	0.025	Pave2 depth (m)
`Pave3Depth`	number (metres unless the description says otherwise)	0.025	Pave3 depth (m)
`Base1Depth`	number (metres unless the description says otherwise)	0.1	Base1 depth (m)
`Base2Depth`	number (metres unless the description says otherwise)	0.1	Base2 depth (m)
`Base3Depth`	number (metres unless the description says otherwise)	0.1	Base3 depth (m)
`Subbase1Depth`	number (metres unless the description says otherwise)	0.3	Subbase1 depth (m)
`Subbase2Depth`	number (metres unless the description says otherwise)	0.3	Subbase2 depth (m)
`Subbase3InnerDepth`	number (metres unless the description says otherwise)	0.3	Subbase3 depth at the inner edge (m)
`Subbase3OuterDepth`	number (metres unless the description says otherwise)	0.3	Subbase3 depth under the face (m)

Points

Point codes are what feature lines, styles and quantity take-off match on — they are the contract this subassembly publishes.

Point	Code	Placed	From	Expression
`P1`	ETW	placed at the attachment point (an absolute offset/elevation)	—	`0 / 0`
`P2`	Hinge	offset + elevation delta from the reference point	P1	`SideShoulderWidth / ShoulderWidthDefaultShoulderSlope`
`P10`	—	offset + elevation delta from the reference point	P1	`0 / -(Pave1Depth)`
`P12`	—	offset + elevation delta from the reference point	P1	`0 / -(Pave1Depth+Pave2Depth)`
`P14`	—	offset + elevation delta from the reference point	P1	`0 / -(Pave1Depth+Pave2Depth+Pave3Depth)`
`P15`	—	offset + elevation delta from the reference point	P1	`0 / -(Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth)`
`P16`	—	offset + elevation delta from the reference point	P1	`0 / -(Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth+Base2Depth)`
`P17`	—	offset + elevation delta from the reference point	P1	`0 / -(Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth+Base2Depth+Base3Depth)`
`P18`	—	offset + elevation delta from the reference point	P1	`0 / -(Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth+Base2Depth+Base3Depth+Subbase1Depth)`
`P19`	—	offset + elevation delta from the reference point	P1	`0 / -(Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth+Base2Depth+Base3Depth+Subbase1Depth+Subbase2Depth)`
`P20`	—	offset + elevation delta from the reference point	P1	`0 / -(Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth+Base2Depth+Base3Depth+Subbase1Depth+Subbase2Depth+Subbase3InnerDepth)`
`P11`	EPS_Pave2	offset + elevation delta from the reference point	P10	`SideExtensionPave2 / ExtensionPave2DefaultShoulderSlope`
`P13`	EPS_Pave3	offset + elevation delta from the reference point	P12	`SideExtensionPave3 / ExtensionPave3DefaultShoulderSlope`
`P21`	—	offset + elevation delta from the reference point	P12	`SideExtensionPave2 / ExtensionPave2DefaultShoulderSlope`
`P22`	—	offset + elevation delta from the reference point	P14	`SideExtensionPave3 / ExtensionPave3DefaultShoulderSlope`
`P3`	EPS_Base1	offset + elevation delta from the reference point	P2	`Side(Pave1Depth+Pave2Depth+Pave3Depth)/(DefaultShoulderSlope-DS) / (Pave1Depth+Pave2Depth+Pave3Depth)DS/(DefaultShoulderSlope-DS)`
`P4`	EPS_Base2	offset + elevation delta from the reference point	P2	`Side(Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth)/(DefaultShoulderSlope-DS) / (Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth)DS/(DefaultShoulderSlope-DS)`
`P5`	EPS_Base3	offset + elevation delta from the reference point	P2	`Side(Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth+Base2Depth)/(DefaultShoulderSlope-DS) / (Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth+Base2Depth)DS/(DefaultShoulderSlope-DS)`
`P6`	EPS_SubBase1	offset + elevation delta from the reference point	P2	`Side(Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth+Base2Depth+Base3Depth)/(DefaultShoulderSlope-DS) / (Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth+Base2Depth+Base3Depth)DS/(DefaultShoulderSlope-DS)`
`P7`	EPS_SubBase2	offset + elevation delta from the reference point	P2	`Side(Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth+Base2Depth+Base3Depth+Subbase1Depth)/(DefaultShoulderSlope-DS) / (Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth+Base2Depth+Base3Depth+Subbase1Depth)DS/(DefaultShoulderSlope-DS)`
`P8`	EPS_SubBase3	offset + elevation delta from the reference point	P2	`Side(Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth+Base2Depth+Base3Depth+Subbase1Depth+Subbase2Depth)/(DefaultShoulderSlope-DS) / (Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth+Base2Depth+Base3Depth+Subbase1Depth+Subbase2Depth)DS/(DefaultShoulderSlope-DS)`
`P9`	Daylight_Sub	offset + elevation delta from the reference point	P1	Side(((Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth+Base2Depth+Base3Depth+Subbase1Depth+Subbase2Depth+Subbase3InnerDepth)+ShoulderWidth(DefaultShoulderSlope-DS))/((DefaultShoulderSlope+(Subbase3InnerDepth-Subbase3OuterDepth)/(ShoulderWidth+(Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth+Base2Depth+Base3Depth+Subbase1Depth+Subbase2Depth)/(DefaultShoulderSlope-DS)))-DS)) / (DefaultShoulderSlope+(Subbase3InnerDepth-Subbase3OuterDepth)/(ShoulderWidth+(Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth+Base2Depth+Base3Depth+Subbase1Depth+Subbase2Depth)/(DefaultShoulderSlope-DS)))(((Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth+Base2Depth+Base3Depth+Subbase1Depth+Subbase2Depth+Subbase3InnerDepth)+ShoulderWidth(DefaultShoulderSlope-DS))/((DefaultShoulderSlope+(Subbase3InnerDepth-Subbase3OuterDepth)/(ShoulderWidth+(Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth+Base2Depth+Base3Depth+Subbase1Depth+Subbase2Depth)/(DefaultShoulderSlope-DS)))-DS))-(Pave1Depth+Pave2Depth+Pave3Depth+Base1Depth+Base2Depth+Base3Depth+Subbase1Depth+Subbase2Depth+Subbase3InnerDepth)

Links

Link	Code	Between	Role
`L1`	Top,SR	P1 → P2	drawn
`L2`	Pave2	P11 → P10	drawn
`L3`	Pave3	P13 → P12	drawn
`L4`	Base1	P14 → P3	drawn
`L5`	Base2	P4 → P15	drawn
`L6`	Base3	P16 → P5	drawn
`L7`	Subbase1	P6 → P17	drawn
`L8`	Subbase2	P18 → P7	drawn
`L9`	Subbase3	P8 → P19	drawn
`L10`	Datum	P20 → P9	drawn
`L11`	Slope_Link	P2 → P3	drawn
`L12`	Slope_Link	P3 → P4	drawn
`L13`	Slope_Link	P5 → P4	drawn
`L14`	Slope_Link	P5 → P6	drawn
`L15`	Slope_Link	P7 → P6	drawn
`L16`	Slope_Link	P7 → P8	drawn
`L17`	Slope_Link	P9 → P8	drawn
`L18`	—	P10 → P1	drawn
`L19`	—	P10 → P12	drawn
`L20`	—	P12 → P14	drawn
`L21`	—	P15 → P14	drawn
`L22`	—	P15 → P16	drawn
`L23`	—	P17 → P16	drawn
`L24`	—	P17 → P18	drawn
`L25`	—	P19 → P18	drawn
`L26`	—	P19 → P20	drawn
`L27`	—	P21 → P11	drawn
`L28`	—	P22 → P13	drawn
`L29`	—	P13 → P21	drawn
`L30`	—	P3 → P22	drawn
`L31`	—	P12 → P21	drawn
`L32`	—	P14 → P22	drawn

Shapes (materials)

Shape	Material code	Boundary points
`SSR`	SR	P1, P2, P3, P22, P13, P21, P11, P10
`SP2`	Pave2	P10, P12, P21, P11
`SP3`	Pave3	P12, P14, P22, P13
`SB1`	Base1	P14, P3, P4, P15
`SB2`	Base2	P15, P4, P5, P16
`SB3`	Base3	P16, P5, P6, P17
`SS1`	Subbase1	P17, P6, P7, P18
`SS2`	Subbase2	P18, P7, P8, P19
`SS3`	Subbase3	P19, P8, P9, P20

Generated page. The tables above are read from the built-in catalogue itself (yu3d_stock_dump), so they always match the version of yucad3d you are running.