yucad3d
Help / User Guide / Subassemblies / Daylight Basin 2

Daylight Basin 2

C3D DaylightBasin2 — detention basin cut into the daylight wing

At a glance

KindSubassembly (composed into an assembly)
DomainRoad
Civil 3D equivalentDaylightBasin2
Geometry25 points, 17 links, 3 shapes
Conditional geometry23 of the points are created inside a branch — which ones appear depends on the parameters and the target surface
Targets2 (surface / offset / elevation targets this subassembly can be linked to)

Parameters

Defaults are the metric values the palette inserts. Every parameter can be driven by an expression or a target.

ParameterTypeDefaultMeaning
Side+1 right of the baseline, −1 leftRight (+1)+1 Right / -1 Left
ForeSlopecross slope as a ratio (−0.02 = 2 % fall)0.333333Foreslope out of the hinge (rise/run)
ForeslopeWidthnumber (metres unless the description says otherwise)1.2Foreslope width (m)
BasinDepthnumber (metres unless the description says otherwise)0Basin depth below the foreslope toe (m)
BasinSlopecross slope as a ratio (−0.02 = 2 % fall)0.25Basin batter (rise/run)
BasinWidthnumber (metres unless the description says otherwise)1.8Flat bottom width (m)
BermWidthnumber (metres unless the description says otherwise)1.8Flat top of the berm in fill (m); 0 omits the berm
OmitBermwhole number / mode selector11 = in fill, omit the basin and daylight from the attach
CutSlopecross slope as a ratio (−0.02 = 2 % fall)0.333333Cut slope beyond the berm
FillSlopecross slope as a ratio (−0.02 = 2 % fall)0.333333Fill slope beyond the berm
OmitDaylightLinknumber (metres unless the description says otherwise)01 = stop at the berm, draw no daylight link
MaxRunnumber (metres unless the description says otherwise)30How far the daylight ray searches (m)
PlaceMaterialwhole number / mode selector30 = line the foreslope, 3 = none
SlopeLimit1cross slope as a ratio (−0.02 = 2 % fall)1First limit (rise/run)
MaterialThickness1number (metres unless the description says otherwise)0.3Lining thickness past limit 1 (m)
SlopeLimit2cross slope as a ratio (−0.02 = 2 % fall)0.5Second limit
MaterialThickness2number (metres unless the description says otherwise)0.15Lining thickness past limit 2 (m)
SlopeLimit3cross slope as a ratio (−0.02 = 2 % fall)0.25Third limit
MaterialThickness3number (metres unless the description says otherwise)0.1Lining thickness past limit 3 (m)
MaterialName1textRip RapMaterial named on the band past limit 1
MaterialName2textRip RapMaterial named on the band past limit 2
MaterialName3textRip RapMaterial named on the band past limit 3

Points

Point codes are what feature lines, styles and quantity take-off match on — they are the contract this subassembly publishes.

PointCodePlacedFromExpression
P1—placed at the attachment point (an absolute offset/elevation)—0 / 0
BT—offset + elevation delta from the reference pointP1Side*(ForeslopeWidth+BasinDepth/BasinSlope+BH/BasinSlope+BasinWidth) / 0-ForeslopeWidth*ForeSlope-BasinDepth+BH
P2 conditional—offset + elevation delta from the reference pointP1Side*ForeslopeWidth / 0-ForeslopeWidth*ForeSlope
P3 conditionalDitch_Inoffset + elevation delta from the reference pointP2Side*BasinDepth/BasinSlope / 0-BasinDepth
P4 conditionalDitch_Outoffset + elevation delta from the reference pointP3Side*BasinWidth / 0
P5 conditionalHinge,Hinge_Cutoffset + elevation delta from the reference pointP4Side*BH/BasinSlope / BH
BML1 conditional—offset + elevation delta from the reference pointP10 / 0-BMT
BML2 conditional—offset + elevation delta from the reference pointP20 / 0-BMT
DC conditionalDaylight_Cutwalk out at a slope until the target surface is met (daylight)P5CutSlope / Side*MaxRun
P2 conditional—offset + elevation delta from the reference pointP1Side*ForeslopeWidth / 0-ForeslopeWidth*ForeSlope
P3 conditionalDitch_Inoffset + elevation delta from the reference pointP2Side*BasinDepth/BasinSlope / 0-BasinDepth
P4 conditionalDitch_Outoffset + elevation delta from the reference pointP3Side*BasinWidth / 0
P5 conditionalHinge,Hinge_Cutoffset + elevation delta from the reference pointP4Side*BH/BasinSlope / BH
BML1 conditional—offset + elevation delta from the reference pointP10 / 0-BMT
BML2 conditional—offset + elevation delta from the reference pointP20 / 0-BMT
DC conditionalDaylight_Cutwalk out at a slope until the target surface is met (daylight)P5CutSlope / Side*MaxRun
P2 conditional—offset + elevation delta from the reference pointP1Side*ForeslopeWidth / 0-ForeslopeWidth*ForeSlope
P3 conditionalDitch_Inoffset + elevation delta from the reference pointP2Side*BasinDepth/BasinSlope / 0-BasinDepth
P4 conditionalDitch_Outoffset + elevation delta from the reference pointP3Side*BasinWidth / 0
P5 conditional—offset + elevation delta from the reference pointP4Side*BH/BasinSlope / BH
BML1 conditional—offset + elevation delta from the reference pointP10 / 0-BMT
BML2 conditional—offset + elevation delta from the reference pointP20 / 0-BMT
P6 conditionalHinge,Hinge_Filloffset + elevation delta from the reference pointP5Side*BermWidth / 0
DF conditionalDaylight_Fillwalk out at a slope until the target surface is met (daylight)P60-FillSlope / Side*MaxRun
DF conditionalDaylight_Fillwalk out at a slope until the target surface is met (daylight)P10-FillSlope / Side*MaxRun

Links

LinkCodeBetweenRole
L1Top,Slope_LinkP1 → P2drawn
L2Top,Slope_LinkP2 → P3drawn
L3Top,DitchP3 → P4drawn
L4Top,Slope_LinkP4 → P5drawn
LCTop,Datum,Daylight_CutP5 → DCdrawn
L1Top,Slope_LinkP1 → P2drawn
L2Top,Slope_LinkP2 → P3drawn
L3Top,DitchP3 → P4drawn
L4Top,Slope_LinkP4 → P5drawn
LCTop,Datum,Daylight_CutP5 → DCdrawn
L1Top,Slope_LinkP1 → P2drawn
L2Top,Slope_LinkP2 → P3drawn
L3Top,DitchP3 → P4drawn
L4Top,Slope_LinkP4 → P5drawn
L5Top,Slope_LinkP5 → P6drawn
LFTop,Datum,Daylight_FillP6 → DFdrawn
LFTop,Datum,Daylight_FillP1 → DFdrawn

Shapes (materials)

ShapeMaterial codeBoundary points
SBMLBasin_MaterialP1, P2, BML2, BML1
SBMLBasin_MaterialP1, P2, BML2, BML1
SBMLBasin_MaterialP1, P2, BML2, BML1

Generated page. The tables above are read from the built-in catalogue itself (yu3d_stock_dump), so they always match the version of yucad3d you are running.